pharma@sz-pharma.com    +86-18241958031
Cont

Have any Questions?

+86-18241958031

clean room in semiconductor manufacturing
video
clean room in semiconductor manufacturing

clean room in semiconductor manufacturing

The inner surface of the clean room should meet the following standards:
Flat and smooth: The inner surface must be flat and smooth, without cracks and falling particles.
Tight interfaces: The interfaces must be tight to prevent the entry of pollutants.
Resistant to cleaning and disinfection: The material must be able to withstand frequent cleaning and disinfection.
Curved design: The junction between the wall and the floor should be curved, or other measures should be taken to reduce accumulation and facilitate cleaning.
Lighting: The illumination in the clean area should not be less than 300 lux, and local lighting can be set up in production areas with special requirements.
Send Inquiry

Product Introduction

Suzhou Pharma Machinery supplies you with the  Gmp Cleaning Room Purification Sandwich Panels Door Clean Room!

 

 

Product Description

 

The production environment and equipment of clean room in semiconductor manufacturing require extremely high requirements and standards:


1. Requirements for the production environment of semiconductor chips
The clean room in semiconductor manufacturing level needs to be clarified according to the regulations of the product production process, and the clean workshop is constructed according to the various design standards of the manufactured products, such as temperature, humidity, cyclone flow requirements, the characteristics of raw and auxiliary materials required for production, and water, electricity, gas and other requirements.
(1). Indoor noise level (empty state): should not be greater than 65dB (A)
(2). The full coverage ratio of the vertical flow clean room should not be less than 60%, and the horizontal unidirectional flow clean room should not be less than 40%, otherwise it is a local unidirectional flow.
(3). The static pressure difference with the outside should not be less than 10Pa, and the static pressure difference between the clean area and the non-clean area with different air cleanliness should not be less than 5Pa.
(4). The amount of fresh air in the clean room should be the maximum of the following two items:
(a) The sum of the amount of fresh air required to compensate for the indoor exhaust volume and maintain the indoor positive pressure value.
(b) Ensure that the amount of fresh air supplied to the clean room per person per hour is not less than 40m3.
(5). The heater of the purification air conditioning system should be equipped with fresh air and over-temperature power-off protection. If point humidification is used, water-free protection should be set; in cold areas, the fresh air system should be equipped with anti-freeze protection measures.


2. Temperature and humidity control of semiconductor chips
The production and storage of clean room in semiconductor manufacturing have extremely strict requirements on temperature and humidity. Therefore, the relative humidity of the semiconductor clean room should be controlled between 40% and 60%, and the allowable error is within a narrow range of ±1%. The allowable error in the photolithography area or in the far ultraviolet treatment area is even smaller, and in other areas it can be put within the range of ±5%.The production temperature of semiconductor chips is very strict. If the temperature is too high or too low, the chip will be scrapped. It should be controlled between 22℃-23℃. Once the humidity control is abnormal, the overall performance of the clean room may decline.

The factors are:

(1). Bacterial growth. Bacteria and other biological contaminants (mold, viruses, fungi, mites) can actively reproduce in an environment with a relative humidity of more than 60%.

(2). The range of room temperature that workers feel comfortable. The relative humidity range of 40% to 60% is the moderate range for human comfort. Too high humidity can make people feel stuffy, while humidity below 30% can make people feel dry, chapped skin, respiratory discomfort and emotional unhappiness.

(3) The generation of electrostatic charges. Semiconductor cleanrooms generally use special equipment or devices to control static charges.
(4) Metal corrosion. The higher the humidity, the faster the speed of the city.
(5). Water absorption and water vapor condensation. All surfaces exposed to the air around the clean room are quickly covered with at least a monomolecular layer of water. When these surfaces are composed of thin metal coatings that can react with water, high humidity can accelerate the reaction.
(6). Degradation of photolithography. In a high relative humidity environment, the expansion of photoresist after the baking cycle is aggravated due to the absorption of water. Photoresist adhesion can also be negatively affected by high relative humidity; lower relative humidity (about 30%) makes photoresist adhesion easier, and even does not require polymerization modifiers.

 

3. Conventional systems in clean workshops In order to make the temperature, humidity and cleanliness of the clean workshop meet production requirements, the conventional configuration systems are as follows:

(1). Air handling equipment.
(2). Air shower room.
(3). Clean room changing room.
(4). Air shower.
(5). Air purifier.
(6). Temperature and humidity control system.
(7). Air conditioning system
(8). Air supply system
(9). Exhaust system
(10). Lighting system
(11). Waste gas and wastewater treatment system.
(12). Pure water system
(13). Air supply system.

 

Model Clean room project
After-Sales Service Provided Overseas Service Center Available
Floor PVC Floor
Cleanliness ISO5--ISO9
Purpose Sterile Environment Production
Suitable Occasion Pharmaceutical Electronic Industry
Material Sandwich Panel
Usage Warehouse, Villa, Dormitories, Temporary Offices, Workshop, Airpurify
Certification ISO, CE, GMP
Warranty

1year

 

Product pictures

 

product-496-372
product-496-372
product-496-372
product-496-372
 

 

Company profile
How To Cooperate With Us?

Our address

NO.188 xiangwei road, near junction of xiangwei road and chengyang road (the second floor of south building inside of haiji feiyue) Xiangcheng district, Suzhou city, Jiangsu province, China

Phone Number

+0086 18241958031

E-mail

pharma@sz-pharma.com

Suzhou-Pharma-Machinery-Co-Ltd- 4 - 1

 

 

 

 

 

FAQ

Q:What products does your company specialized in?
A:Our company specialized in cleanroom turnkey project,air clean equipment and extraction
machinery.


Q:What industry of cleanroom you can supply?
A:Hospital,laboratory,pharmaceutical,medical,electronic,biological,food andbeverage,
cosmeticsindustry,etc.


Q:Does the cleanroom cost include installation and freight?
freightaccordingtoyouraddress.


Q:How does a cleanroom work?
A:A cleanroom provides a controlled,isolated environment for handling contamination-sensitive
substances or for protecting the exterior environment from dangerous substances in the controlled
area.The density of sub-micron and larger airbome particle contamination inside a cleanroom is
kept within tightly controlled limits by forcing clean,filtered air into the cleanroom.


Q:Can I get special design and function?
A:Yes,We are very pleased to be able to provide you with new designs,or to manufacture according
to your drawings.


Q:How can you guarantee high level manufacturing process and installation?
A:We are professional suppliers for more than 15years.We have the best designers,engineers.We
will design and manufacture according to the standards of the cleanrooms.We have full experience
installation workers,they can make perfect buildings with professional skills.

Hot Tags: clean room in semiconductor manufacturing, China clean room in semiconductor manufacturing manufacturers, suppliers, factory

Send Inquiry

(0/10)

clearall