pharma@sz-pharma.com    +86-18241958031
Cont

Have any Questions?

+86-18241958031

Jan 05, 2026

Selection Of Floor Materials For Pharmaceutical Cleanrooms

The following are the most commonly used floor finishes in pharmaceutical factories:

Terrazzo Flooring: It boasts excellent integrity, a smooth surface, and resistance to dust generation. It is washable and anti-static, but has no elasticity. It is usually applied in workshops requiring frequent scrubbing, such as sub-packaging workshops, tablet and capsule workshops, laboratories, washrooms, changing rooms, and crystallization sections.

Double-layer Flooring: It enables air return through the floor, featuring good air permeability, but has a high cost and poor elasticity while offering decent comfort. It is often used in large-area vertical unidirectional flow cleanrooms in pharmaceutical plants.

Plastic Flooring: It has a smooth surface with slight elasticity, is resistant to dust and easy to clean, and also features wear resistance and corrosion resistance. However, it is prone to static electricity and aging under ultraviolet radiation, making it unsuitable for areas regularly sterilized with UV lamps. It is generally used in changing rooms, packaging rooms, laboratories and other spaces. Due to the different expansion and contraction properties between plastic sheets and concrete substrates, it should not be used in large-area workshops, otherwise it may cause delamination.

Coating Flooring: It has the same advantages as terrazzo flooring and is relatively wear-resistant, but vulnerable to damage from dragging objects. It has high requirements for substrate treatment and is prone to edge curling and peeling. It is commonly used in the clean areas of pharmaceutical factories.

cleanroom floor

ISO cleanroom

Acid-resistant Ceramic Tile Flooring: Lay with acid-resistant mortar, it has good corrosion resistance, but is brittle and cannot withstand impact. Once cracked, its corrosion resistance will be reduced. This type of flooring can be used in sections of raw material workshops exposed to corrosive media. Given its complex construction process and high cost, it is suitable for local areas where corrosive media may drip or leak. For example, equipment involving corrosive media can be centrally arranged, and the corresponding floor area can be enclosed with water retaining lines, with acid-resistant ceramic tile flooring paved inside the lines.

Roll and Sheet Flooring: It is smooth, wear-resistant, slightly elastic, dust-proof, easy to clean and simple to construct. However, it is susceptible to static electricity and UV aging, and may bulge when applied in large areas. It is usually used in the controlled areas of pharmaceutical factories.

FRP (Fiberglass Reinforced Plastic) Flooring: It has good corrosion resistance and integrity, but tends to bulge and is suitable for small-area applications. It is often used in corrosive sections of raw material workshops in pharmaceutical factories.

As one of the most crucial components of the cleanroom envelope structure in pharmaceutical factories, floor material selection should not only meet the general requirements for floors, but also take into account factors such as dust generation rate, construction difficulty and cost. At present, terrazzo flooring, which features excellent integrity and high rigidity, is generally the preferred choice for cleanrooms in pharmaceutical factories. To prevent dust accumulation and bacterial growth, terrazzo floors must be protected against cracking and moisture regain. During construction, measures such as tamping backfill soil, increasing floor thickness, using high-quality cement (the strength grade of cement for cement mortar substrates shall not be lower than 42.5 MPa) and proper reinforcement (for large-area workshops) can be adopted to prevent floor cracking. To avoid moisture regain, construction measures including increasing the thickness of concrete and crushed stone layers, and adding waterproof layers (such as one layer of felt with two coats of bitumen) in high-humidity areas are available.

For floors requiring acid and alkali resistance, coatings such as polyurethane, epoxy resin, perchlorovinyl, ethylene resin, chlorinated rubber and neoprene can be used. For floors with oil resistance requirements, coatings like epoxy resin, perchlorovinyl, alkyd resin and nitrocellulose are applicable.

In most clean workshops of pharmaceutical factories, terrazzo flooring is a reliable first choice provided that construction is carried out in accordance with standards and floor quality is guaranteed.

Suzhou Pharma Machinery Co.,Ltd.

2026/01/05

Gino

Send Inquiry